LSI-Logic MPT-Fusion » История » Версия 1
Андрей Волков, 2015-03-13 12:50
| 1 | 1 | Андрей Волков | h1. LSI-Logic MPT-Fusion |
|---|---|---|---|
| 2 | |||
| 3 | h2. LSI-Logic-SAS1064E-B3-SAS3042E |
||
| 4 | |||
| 5 | *./sasflash -listall* |
||
| 6 | |||
| 7 | <pre> |
||
| 8 | **************************************************************************** |
||
| 9 | LSI Corporation SAS FLASH Utility. |
||
| 10 | |||
| 11 | SASFlash Version 1.30.00.00 (2011.08.24) |
||
| 12 | |||
| 13 | Copyright (c) 2006-2011 LSI Corporation. All rights reserved. |
||
| 14 | **************************************************************************** |
||
| 15 | |||
| 16 | Adapter Selected is a LSI SAS 1064E(B3): |
||
| 17 | |||
| 18 | Num Ctlr FW Ver NVDATA x86-BIOS EFI-BSD PCI Addr |
||
| 19 | ----------------------------------------------------------------------- |
||
| 20 | |||
| 21 | 1 1064E(B3) 01.23.39.00 2b.86 06.18.05.00 No Image 00:09:00:00 |
||
| 22 | |||
| 23 | |||
| 24 | Finished Processing Commands Successfully. |
||
| 25 | Exiting SASFlash. |
||
| 26 | |||
| 27 | </pre> |
||
| 28 | |||
| 29 | *lsiutil -p 1 -i -s* |
||
| 30 | |||
| 31 | <pre> |
||
| 32 | LSI Logic MPT Configuration Utility, Version 1.62, January 14, 2009 |
||
| 33 | |||
| 34 | 1 MPT Port found |
||
| 35 | |||
| 36 | ============================================================================== |
||
| 37 | |||
| 38 | /proc/mpt/ioc0 LSI Logic SAS1064E B3 MPT 105 Firmware 01172700 IOC 0 |
||
| 39 | |||
| 40 | Seg/Bus/Dev/Fun Board Name Board Assembly Board Tracer |
||
| 41 | 0 9 0 0 SAS3042E L3-25006-02C P62200BGKW540H |
||
| 42 | |||
| 43 | Current Port State |
||
| 44 | ------------------ |
||
| 45 | SAS1064E's links are 1.5 G, 1.5 G, down, down |
||
| 46 | |||
| 47 | Software Version Information |
||
| 48 | ---------------------------- |
||
| 49 | Current active firmware version is 01172700 (1.23.39) |
||
| 50 | Firmware image's version is MPTFW-01.23.39.00-IE |
||
| 51 | LSI Logic |
||
| 52 | x86 BIOS image's version is MPTBIOS-6.18.05.00 (2008.05.14) |
||
| 53 | |||
| 54 | Firmware Settings |
||
| 55 | ----------------- |
||
| 56 | SAS WWID: 500605b000144f2c |
||
| 57 | Multi-pathing: Disabled |
||
| 58 | SATA Native Command Queuing: Disabled |
||
| 59 | SATA Write Caching: Disabled |
||
| 60 | SATA Maximum Queue Depth: 1 |
||
| 61 | Device Missing Report Delay: 3 seconds |
||
| 62 | Device Missing I/O Delay: 3 seconds |
||
| 63 | Phy Parameters for Phynum: 0 1 2 3 |
||
| 64 | Link Enabled: Yes Yes Yes Yes |
||
| 65 | Link Min Rate: 1.5 1.5 1.5 1.5 |
||
| 66 | Link Max Rate: 3.0 3.0 3.0 3.0 |
||
| 67 | SSP Initiator Enabled: Yes Yes Yes Yes |
||
| 68 | SSP Target Enabled: No No No No |
||
| 69 | Port Configuration: Auto Auto Auto Auto |
||
| 70 | Target IDs per enclosure: 1 |
||
| 71 | Persistent mapping: Enabled |
||
| 72 | Physical mapping type: Enclosure/Slot |
||
| 73 | Target ID 0 reserved for boot: Yes |
||
| 74 | Starting slot (direct attach): 1 |
||
| 75 | Target IDs (physical mapping): 8 |
||
| 76 | Interrupt Coalescing: Enabled, timeout is 16 us, depth is 4 |
||
| 77 | |||
| 78 | Persistent Mappings |
||
| 79 | ------------------- |
||
| 80 | No persistent entries found |
||
| 81 | |||
| 82 | B___T___L Type Vendor Product Rev SASAddress PhyNum |
||
| 83 | 0 1 0 Disk ATA OCZ-AGILITY3 2.25 1221000000000000 0 |
||
| 84 | 0 2 0 Disk ATA OCZ-AGILITY3 2.25 1221000001000000 1 |
||
| 85 | </pre> |