LSI-Logic MPT-Fusion » История » Редакция 3
Редакция 2 (Андрей Волков, 2015-03-13 12:57) → Редакция 3/11 (Андрей Волков, 2015-03-13 12:59)
h1. LSI-Logic MPT-Fusion
h2. LSI-Logic-SAS1064E-B3-SAS3042E
h3. Смотрим
*./sasflash -listall*
<pre>
****************************************************************************
LSI Corporation SAS FLASH Utility.
SASFlash Version 1.30.00.00 (2011.08.24)
Copyright (c) 2006-2011 LSI Corporation. All rights reserved.
****************************************************************************
Adapter Selected is a LSI SAS 1064E(B3):
Num Ctlr FW Ver NVDATA x86-BIOS EFI-BSD PCI Addr
-----------------------------------------------------------------------
1 1064E(B3) 01.23.39.00 2b.86 06.18.05.00 No Image 00:09:00:00
Finished Processing Commands Successfully.
Exiting SASFlash.
</pre>
*lsiutil -p 1 -i -s*
<pre>
LSI Logic MPT Configuration Utility, Version 1.62, January 14, 2009
1 MPT Port found
==============================================================================
/proc/mpt/ioc0 LSI Logic SAS1064E B3 MPT 105 Firmware 01172700 IOC 0
Seg/Bus/Dev/Fun Board Name Board Assembly Board Tracer
0 9 0 0 SAS3042E L3-25006-02C P62200BGKW540H
Current Port State
------------------
SAS1064E's links are 1.5 G, 1.5 G, down, down
Software Version Information
----------------------------
Current active firmware version is 01172700 (1.23.39)
Firmware image's version is MPTFW-01.23.39.00-IE
LSI Logic
x86 BIOS image's version is MPTBIOS-6.18.05.00 (2008.05.14)
Firmware Settings
-----------------
SAS WWID: 500605b000144f2c
Multi-pathing: Disabled
SATA Native Command Queuing: Disabled
SATA Write Caching: Disabled
SATA Maximum Queue Depth: 1
Device Missing Report Delay: 3 seconds
Device Missing I/O Delay: 3 seconds
Phy Parameters for Phynum: 0 1 2 3
Link Enabled: Yes Yes Yes Yes
Link Min Rate: 1.5 1.5 1.5 1.5
Link Max Rate: 3.0 3.0 3.0 3.0
SSP Initiator Enabled: Yes Yes Yes Yes
SSP Target Enabled: No No No No
Port Configuration: Auto Auto Auto Auto
Target IDs per enclosure: 1
Persistent mapping: Enabled
Physical mapping type: Enclosure/Slot
Target ID 0 reserved for boot: Yes
Starting slot (direct attach): 1
Target IDs (physical mapping): 8
Interrupt Coalescing: Enabled, timeout is 16 us, depth is 4
Persistent Mappings
-------------------
No persistent entries found
B___T___L Type Vendor Product Rev SASAddress PhyNum
0 1 0 Disk ATA OCZ-AGILITY3 2.25 1221000000000000 0
0 2 0 Disk ATA OCZ-AGILITY3 2.25 1221000001000000 1
</pre>
h3. Перепрошиваем Firmware
*./sasflash -fwall 6ei_r_ld.fw*
<pre>
****************************************************************************
LSI Corporation SAS FLASH Utility.
SASFlash Version 1.30.00.00 (2011.08.24)
Copyright (c) 2006-2011 LSI Corporation. All rights reserved.
****************************************************************************
Ignoring All other commands except for output flags
Attempting to flash firmware to LSI SAS 1064E(B3):
Executing Operation: Flash Firmware Image
Checksum Passed: 00000000
Verifying NVDATA Compatibility. . .
NVDATA Versions Compatible
Product ID and Vendor ID match verified.
Valid BootLoader Image verified.
Beginning Firmware Download
Firmware Download: SUCCESSFUL!
Verifying the image flashed correctly. . .
Firmware Flash: SUCCESSFUL!
Resetting Adapter:
Adapter Successfully reset.
Updating VPD data!
VPD update not needed
Finished Processing Commands Successfully.
Exiting SASFlash.
</pre>
h3. Смотрим
*./sasflash -listall*
<pre>
<code class="diff">
./sasflash -listall
****************************************************************************
LSI Corporation SAS FLASH Utility.
SASFlash Version 1.30.00.00 (2011.08.24)
Copyright (c) 2006-2011 LSI Corporation. All rights reserved.
****************************************************************************
Adapter Selected is a LSI SAS 1064E(B3):
Num Ctlr FW Ver NVDATA x86-BIOS EFI-BSD PCI Addr
-----------------------------------------------------------------------
-1
1 1064E(B3) 01.23.39.00 2b.86 06.18.05.00 No Image 00:09:00:00
+1 1064E(B3) 01.23.46.00 2b.90 06.18.05.00 No Image 00:09:00:00
Finished Processing Commands Successfully.
Exiting SASFlash.
</code>
</pre>
h3. Перепрошиваем BIOS
<pre>
</pre>